[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[plamo:04851] HP Vectra VT 6/150 X Setup



矢野です。

どうしても、Xの設定ができません。(1ヵ月以上)
どうか、よきアドバイスをお願いします。

XF86Setupで、Xの設定をすると、画面の左上の1/4部分が画面全体に
「おめでとうございます、サ」と表示されます。

  AB ----> A
  CD

Aのエリアの部分が画面全体に拡大表示する感じです。
右側と下側、つまり、B,C,Dエリアの部分は画面からはみ出してみえません。

機種      HP Vectar VT 6/150
モニター  三菱  DR17G
Plamo Ver. 1.4.4 for AT  おすすめ  かんな  ディスクトップでインストール

Turbo Linux Ver. 4.2 と Laser5 Ver. 6.0 は正常に設定できます。

そのときの設定ファイル XF86Config を保存して、
Plamo でいろいろ流用しましたが駄目でした。

原因が不明なので BIOS を最新のものにアップデートしました。

BIOSの内容
System BIOS Version  GV.06.10
Video Board          MILLENNIUM. Ver : 838-9, VRAM: 2 MB
PnP Boad Activation
  Full , None , Bootable Only にそれぞれ切り替えて試しました。
  結果は変わりませんでした。

Windows NT 4.0 ワークステーション使用時の診断プログラムの内容

アダプタ
設定          1024*768*65536 60Hz
種類          mag_mil 互換ディスプレイアダプター
文字列        MAG Millennium
メモリー      2MB
チップの種類  MGA-2064W B2 R2
DACの種類     TI TVP3026(175MHz)

XF86Setupの設定

カード        Matrox Millennium 2MB

  X付属の Matrox のドキュメントによりますと、詳細設定はしないで、
  自動認識させるのですね。

  チップセットと RamDac の設定はしてはいけないという記述がありました。

  一応、チップセット mga2064w , RamDac TVP3026 の選択を
  それぞれ試してみました。

  チップセット mga2064w を選択して、設定終了すると、
  _X11TransScketUNIXConnect: Can't connect: errno = 111
  と何回か表示され、しばらくすると、
  画面の左上の1/4部分が画面全体に表示されますが、
  チェック模様でのままで、停止します。
 「おめでとうございます、サ」と表示されません。

  RamDac TVP3026 の選択の有り/無しにかかわらず。
  画面の左上の1/4部分が画面全体に表示されます。
 「おめでとうございます、サ」と表示されます。

ディスプレイ  Non-Interlaced SVGA, 1024*768 @ 60 Hz, 800*600 @ 72 Hz
              水平周波数  31.5-48.5 Hz  垂直周波数  55-90 Hz

解像度        1024*768  256色

XF86_SVGAのリンク状態

cd /usr/X11R6/bin
ls -la X

  X -> /var/X11R6/bin/X

cd /var/X11R6/bin/
ls -la X

  X -> /usr/X11R6/bin/XF86_SVGA

cd /usr/X11R6/bin
ls -la XF86_SVGA

  XF86_SVGA

何故、
cd /usr/X11R6/bin
ls -la X

  X -> /usr/X11R6/bin/XF86_SVGA

とスマートにインストールされていないのでしょうか?
一応、X から XF86_SVGA にリンクしているみたいですが。

XF86Config の内容

Section "Files"
   RgbPath    "/usr/X11R6/lib/X11/rgb"
   FontPath   "/usr/X11R6/lib/X11/fonts/local"
   FontPath   "/usr/X11R6/lib/X11/fonts/misc:unscaled"
   FontPath   "/usr/X11R6/lib/X11/fonts/75dpi:unscaled"
   FontPath   "/usr/X11R6/lib/X11/fonts/100dpi:unscaled"
   FontPath   "/usr/X11R6/lib/X11/fonts/Type1"
   FontPath   "/usr/X11R6/lib/X11/fonts/Speedo"
   FontPath   "/usr/X11R6/lib/X11/fonts/misc"
   FontPath   "/usr/X11R6/lib/X11/fonts/75dpi"
   FontPath   "/usr/X11R6/lib/X11/fonts/100dpi"
EndSection

Section "ServerFlags"
EndSection

Section "Keyboard"
   Protocol        "Standard"
   XkbRules        "xfree86"
   XkbModel        "jp106"
   XkbLayout       "jp"
EndSection

Section "Pointer"
   Protocol        "PS/2"
   Device          "/dev/mouse"
   Emulate3Timeout 50
   Resolution      100
   Buttons         3
   Emulate3Buttons
EndSection

Section "Monitor"
   Identifier      "Primary Monitor"
   VendorName      "Unknown"
   ModelName       "Unknown"
   HorizSync       31.5-48.5
   VertRefresh     55-90
   Modeline  "320x204"    25.18 320 344 376 400 204 206 225 0
EndSection

Section "Device"
   Identifier      "Primary Card"
   VendorName      "Unknown"
   BoardName       "Matrox Millennium 2MB"
   Clocks          25.18
VideoRam 2048

EndSection

Section "Screen"
   Driver          "Accel"
   Device          "Primary Card"
   Monitor         "Primary Monitor"
   DefaultColorDepth 8
   SubSection "Display"
      Depth        8
      Modes        "320x204"
   EndSubSection
   SubSection "Display"
      Depth        15
      Modes        "320x204"
   EndSubSection
   SubSection "Display"
      Depth        16
      Modes        "320x204"
   EndSubSection
   SubSection "Display"
      Depth        24
      Modes        "320x204"
   EndSubSection
   SubSection "Display"
      Depth        32
      Modes        "320x204"
   EndSubSection
EndSection

Section "Screen"
   Driver          "SVGA"
   Device          "Primary Card"
   Monitor         "Primary Monitor"
   DefaultColorDepth 8
   SubSection "Display"
      Depth        8
      Modes        "320x204"
   EndSubSection
   SubSection "Display"
      Depth        15
      Modes        "320x204"
   EndSubSection
   SubSection "Display"
      Depth        16
      Modes        "320x204"
   EndSubSection
   SubSection "Display"
      Depth        24
      Modes        "320x204"
   EndSubSection
   SubSection "Display"
      Depth        32
      Modes        "320x204"
   EndSubSection
EndSection

Section "Screen"
   Driver          "VGA16"
   Device          "Primary Card"
   Monitor         "Primary Monitor"
   SubSection "Display"
      Depth        4
      Modes        "320x204"
   EndSubSection
EndSection

Section "Screen"
   Driver          "VGA2"
   Device          "Primary Card"
   Monitor         "Primary Monitor"
   SubSection "Display"
      Depth        1
      Modes        "320x204"
   EndSubSection
EndSection

Section "Screen"
   Driver          "Mono"
   Device          "Primary Card"
   Monitor         "Primary Monitor"
   SubSection "Display"
      Depth        1
      Modes        "320x204"
   EndSubSection
EndSection

XF86Setup で、解像度を 1024*768 を指定したのにかかわらず、
XF86Config の中に、1024x768 の記述が無かったので、
エディタで強制的に、 320x204 の部分を 1024x768 に直してみましたが、
結果は変わりませんでした。

xinit の結果

XFree86 Version 3.3.3.1 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: December 29 1998
	If the server is older than 6-12 months, or if your card is newer
	than the above date, look for a newer version before reporting
	problems.  (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.0.35 i686 [ELF] 
Configured drivers:
  SVGA: server for SVGA graphics adaptors (Patchlevel 0):
      NV1, STG2000, RIVA128, RIVATNT, ET4000, ET4000W32, ET4000W32i,
      ET4000W32i_rev_b, ET4000W32i_rev_c, ET4000W32p, ET4000W32p_rev_a,
      ET4000W32p_rev_b, ET4000W32p_rev_c, ET4000W32p_rev_d, ET6000, ET6100,
      et3000, pvga1, wd90c00, wd90c10, wd90c30, wd90c24, wd90c31, wd90c33,
      gvga, ati, sis86c201, sis86c202, sis86c205, sis86c215, sis86c225,
      sis5597, sis5598, sis6326, tvga8200lx, tvga8800cs, tvga8900b,
      tvga8900c, tvga8900cl, tvga8900d, tvga9000, tvga9000i, tvga9100b,
      tvga9200cxr, tgui9400cxi, tgui9420, tgui9420dgi, tgui9430dgi,
      tgui9440agi, cyber9320, tgui9660, tgui9680, tgui9682, tgui9685,
      cyber9382, cyber9385, cyber9388, cyber9397, cyber9520, 3dimage975,
      3dimage985, clgd5420, clgd5422, clgd5424, clgd5426, clgd5428,
      clgd5429, clgd5430, clgd5434, clgd5436, clgd5446, clgd5480, clgd5462,
      clgd5464, clgd5465, clgd6205, clgd6215, clgd6225, clgd6235, clgd7541,
      clgd7542, clgd7543, clgd7548, clgd7555, clgd7556, ncr77c22, ncr77c22e,
      cpq_avga, mga2064w, mga1064sg, mga2164w, mga2164w AGP, mgag200,
      mgag100, oti067, oti077, oti087, oti037c, al2101, ali2228, ali2301,
      ali2302, ali2308, ali2401, cl6410, cl6412, cl6420, cl6440, video7,
      ark1000vl, ark1000pv, ark2000pv, ark2000mt, mx, realtek, s3_virge,
      AP6422, AT24, AT3D, s3_svga, NM2070, NM2090, NM2093, NM2097, NM2160,
      NM2200, ct65520, ct65525, ct65530, ct65535, ct65540, ct65545, ct65546,
      ct65548, ct65550, ct65554, ct65555, ct68554, ct69000, ct64200,
      ct64300, mediagx, V1000, V2x00, p9100, spc8110, generic
(using VT number 7)

XF86Config: /etc/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: rules: "xfree86"
(**) XKB: model: "jp106"
(**) XKB: layout: "jp"
(**) Mouse: type: PS/2, device: /dev/mouse, resolution: 100
(**) Mouse: buttons: 3, 3 button emulation (timeout: 50ms)
(**) SVGA: Graphics device ID: "Primary Card"
(**) SVGA: Monitor ID: "Primary Monitor"
(--) SVGA: Invalid vertical timing for mode "320x204". Deleted.
Warning: The directory "/usr/X11R6/lib/X11/fonts/local" does not exist.
         Entry deleted from font path.
Warning: The directory "/usr/X11R6/lib/X11/fonts/100dpi" does not exist.
         Entry deleted from font path.
Warning: The directory "/usr/X11R6/lib/X11/fonts/Type1" does not exist.
         Entry deleted from font path.
Warning: The directory "/usr/X11R6/lib/X11/fonts/Speedo" does not exist.
         Entry deleted from font path.
Warning: The directory "/usr/X11R6/lib/X11/fonts/100dpi" does not exist.
         Entry deleted from font path.
(**) FontPath set to 
"/usr/X11R6/lib/X11/fonts/misc:unscaled,/usr/X11R6/lib/X11/fonts/75dpi:unsca
led,/usr/X11R6/lib/X11/fonts/misc,/usr/X11R6/lib/X11/fonts/75dpi"
(--) SVGA: chipset:  generic
(**) SVGA: videoram: 2048k
(**) SVGA: clocks:  25.18
(**) SVGA: Using 8 bpp, Depth 8, Color weight: 666
(--) SVGA: Using builtin driver modes
(--) SVGA: Builtin Mode: 320x200
(--) SVGA: Virtual resolution set to 320x204
(--) SVGA: SpeedUp code selection modified because virtualX != 1024

waiting for X server to shut down 

チップセット mga2064w
XF86Setup で、解像度を 1024*768 を指定したのに、

(--) SVGA: chipset:  generic
(--) SVGA: Builtin Mode: 320x200
(--) SVGA: Virtual resolution set to 320x204

このメッセージが出るのは気になります。

以上です、お教えて下さい。

--
お休み         Z 矢野  康秀  岐阜県大垣市
              z   http://www.mirai.ne.jp/~yasuhi/ml/
   ●⌒⌒●  z    yasuhide@aa.uno.ne.jp ― 中継 LIVE →
 / 〜^〜 \       yasuhi@he.mirai.ne.jp,yasuhi@yellow.plala.or.jp
│ │-  -│ │
│  \  /  │
 〜/    \〜

Follow-Ups
[plamo:04852] Re: HP Vectra VT 6/150 X Setup, heron

[検索ページ] [メール一覧]
Plamo ML 公開システム