[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[plamo:17966] PC-9821 V200 Nr15 Nr13 での動作報告



宮本です。
PC-9821 Nr15 の Plamo98 3.0 で pcnet_cs の認識もうまく行きました。
やり方は、V200 の ne2k-pci と同じで、Network device support->Ethernet (10 or 100Mbit)->NEC PC-9800 C-bus cards を [ ] 、Network device support->Ethernet (10 or 100Mbit)->PCI NE2000 and clones supportを<M>にしてkernelを再構築(make modules も)して 8390.o を自動生成して、pcnet_cs.c をcompile しまして、8390.o と同じ directory に置きました。pcmcia/config に LPC-2T の entry が有りましたので、reboot したところ、認識しました。
X の設定も Nr15(Trident 9385) と V200(Matrox Mystique)の 両方でうまく行きました。
V200 は Plamo の site に up されている XF86Config では、うまく行きませんでしたので(pex5 と xie が見当たりませんでした。Plamo98 2.2 ではありました。xfree86.org へ取りにいけばいいのでしょうが。) xf86config でつくり一部参考にさせてもらいました。
Nr15 は xf86config で作りました。
modules.conf は、両方とも、そのまま copy させてもらいました。(modules.confの部分は、全くわかりません。勉強不足です。情報源はどこでしょうか?)
mp3 が聞けました。有難うございました。
あと、Nr13(cirrus CL-DG7555) にも Plamo98 3.0 を install したのですが、XFree86 4.2.0 はcirrus 7555 をsupport していないので(The following chips are supported in 3.3.6 but not in 4.2.0: 6410, 6412, 6420, 6440, 5420, 5422, 5424, 5426, 5428, 5429, 6205, 6215, 6225, 6235, 7541, 7542,7543, 7555 and 7556.)X はだめのようです。
XFree86 3.3.6 では support しているようなので、Plamo98 2.2 を再 install して、X の設定を頑張っているのですが、うまくいっていません。
症状は、一応は立ち上がるのですが ctrl-alt-del も ctrl-alt-bs も利かなくなり、exit すると、画面がちらつき、全く key を受け付けなくなり、電源を切るしかありません。
次のような文章があり
'CL-GD7555  Limited untested support, without auto-detection, has been provided for this chip which is a 64-bit extension of the 754x family. Use a Chipset "clgd7555" line.'
xf86configで作ったXF86Configの一部は、次のようです
Section "Device"
    Identifier  "vid"
    VendorName  "ven"
    BoardName   "mod"
    VideoRam    2048
    Chipset "clgd7555"
    # Option	"no_bitblt"
    # Option	"fast_dram"
    Option	"linear"
    Option	"noaccel"
# Use Option "no_bitblt" if you have graphics problems. If that fails
# try Option "noaccel".
# Refer to /usr/X11R6/lib/doc/README.cirrus.
# To allow linear addressing, uncomment the Option line and the
# address that the card maps the framebuffer to.
X server は XF98_SVGA です。
なお、X server を XF98_NEC480 にすると ColorDepth 8,"640x480" で、全画面ではありませんが、一応は動きます。
やはり "CL-GD7555  Limited untested support" ということでしょう
hiroyuki_miyamoto@mail.goo.ne.jp


[検索ページ] [メール一覧]
Plamo ML 公開システム