[plamo:18284] pcmcia(PCC-TX)

[kengoo]

石塚と申します。
ノートＰＣ（ＭＮ−３３０−Ｘ１３）にcorega EastEther PCC-TXを認識
させようと思ってうまくいかず投稿しました。
pcmcia HOWTOを参考に
    /etc/rc.d/rc.pcmcia
    /etc/pcmcia/config.opts
を変更してます。よろしくお願いします。

/etc/rc.d/rc.pcmcia（抜粋）
    # Slackware startup options go right here:
    # Should be either i82365 or tcic
    PCIC=i82365
    # Put socket driver timing parameters here
    PCIC_OPTS=irq_list=9,10,11,12,14,15 poll_interval=100
    # Put pcmcia_core options here
    CORE_OPTS=
    # Put cardmgr options here
    CARDMGR_OPTS=
    # To set the PCMCIA scheme at startup...
    SCHEME=

/etc/pcmcia/config.opts（抜粋）
    # First built-in serial port
    exclude irq 4
    # Second built-in serial port
    exclude irq 3
    # First built-in parallel port
    exclude irq 7

less /var/lib/pcmcia/stab
Socket 0: Corega PCC-TX Fast Ethernet
Socket 1: empty

cardctl ident
Socket 0:
  product info: "corega K.K.", "corega FastEther PCC-TX"
  manfid: 0xc00f, 0x0000
  function: 6 (network)
Socket 1:
  no product info available

cardctl config
Socket 0:
  Vcc 5.0V  Vpp1 0.0V  Vpp2 0.0V
Socket 1:
  not configured

tail -f /var/log/messages（カードを抜き差し）
Apr 10 10:51:53 localhost cardmgr[53]: socket 0: Corega PCC-TX Fast Ethernet
Apr 10 10:51:53 localhost cardmgr[53]: executing: 'modprobe 8390'
Apr 10 10:51:54 localhost cardmgr[53]: + modprobe: Can't locate module 8390
Apr 10 10:51:54 localhost cardmgr[53]: modprobe exited with status 255
Apr 10 10:51:54 localhost cardmgr[53]: module /lib/modules/2.4.19/net/8390.o
not available
Apr 10 10:51:54 localhost cardmgr[53]: executing: 'modprobe pcnet_cs'
Apr 10 10:51:54 localhost kernel: pcnet_cs: unable to read hardware net
address for io base 0x320
Apr 10 10:51:54 localhost cardmgr[53]: get dev info on socket 0 failed: No
such device
Apr 10 10:56:43 localhost cardmgr[53]: executing: 'modprobe -r pcnet_cs'
Apr 10 10:56:44 localhost cardmgr[53]: executing: 'modprobe -r 8390'

dmesg（カードをさしたまま起動）
Linux Kernel Card Services 3.1.22
  options:  [pci] [cardbus] [pm]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Intel PCIC probe: not found.
PCI: Found IRQ 10 for device 00:0f.0
PCI: No IRQ known for interrupt pin B of device 00:0f.1. Please try using
pci=biosirq.
Yenta IRQ list 0ad8, PCI irq10
Socket status: 30000010
Yenta IRQ list 0ad8, PCI irq0
Socket status: 30000006
apm_do_idle failed (0)
cs: IO port probe 0x0c00-0x0cff: excluding 0xc00-0xc07
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x200-0x207 0x220-0x22f
0x300-0x307 0x378-0x37f 0x388-0x38f 0x398-0x39f 0x408-0x40f 0x480-0x48f
0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
cs: memory probe 0xa0000000-0xa0ffffff: clean.
eth0: pcnet_reset_8390() did not complete.
pcnet_cs: unable to read hardware net address for io base 0x320