[plamo:18840] Re: pcmcia(PCC-TX)

[kengoo]

石塚です。
いろいろ試行錯誤しつつ１ヶ月たってしまいましたが、
Re: [plamo:18381]の続きになります。
試行錯誤を要約すると、[plamo:08182] kernel 2.4.0の記事を参考にして、
kernel組み込みのpcmciaは使わず、pcmcia-csを使うように
しました。
下記のurlも参考になりました。
http://www.turbolinux.co.jp/dcforum/DCForumID11/3912.html#6

これで大丈夫なのでしょうか？
音も２回高いビープ音がなります。

#dmesg（抜粋）
Linux PCMCIA Card Services 3.2.0
  kernel build: 2.4.19 #1 Fri May 9 21:54:22 JST 2003
  options:  [pci] [cardbus] [apm]
Intel ISA/PCI/CardBus PCIC probe:
PCI: Found IRQ 10 for device 00:0f.0
PCI: No IRQ known for interrupt pin B of device 00:0f.1.
  TI 1131 rev 01 PCI-to-CardBus at slot 00:0f, mem 0x10000000
    host opts [0]: [pci + serial irq] [pci irq 10] [lat 64/176] [bus 1/5]
    host opts [1]: [pci + serial irq] [no pci irq] [lat 64/176] [bus 6/10]
    ISA irqs (scanned) = 3,4,5,7,9,11 status change on irq 11
cs: memory probe 0xa0000000-0xa0ffffff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x398-0x39f 0x3c0-0x3df
0x408-0x40f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x03a0-0x03bf: clean.
cs: IO port probe 0x03e0-0x0407: clean.
cs: IO port probe 0x0410-0x047f: clean.
cs: IO port probe 0x0490-0x04cf: clean.
cs: IO port probe 0x04d8-0x04ff: clean.
cs: IO port probe 0x0800-0x08ff: clean.
cs: IO port probe 0x0a00-0x0aff: clean.
cs: IO port probe 0x0c00-0x0cff: excluding 0xc00-0xc07
eth0: NE2000 (DL10019 rev 30): io 0x300, irq 3, hw_addr 00:00:F4:5E:2D:B2

#tail -f /var/log/messages（カードを抜き差し）
May 10 14:11:06 localhost cardmgr[51]: executing: './network stop eth0'
May 10 14:11:06 localhost cardmgr[51]: executing: 'modprobe -r pcnet_cs'
May 10 14:11:07 localhost cardmgr[51]: executing: 'modprobe -r 8390'
May 10 14:11:10 localhost cardmgr[51]: socket 0: Corega PCC-TX Fast Ethernet
May 10 14:11:10 localhost cardmgr[51]: executing: 'modprobe 8390'
May 10 14:11:10 localhost cardmgr[51]: executing: 'modprobe pcnet_cs'
May 10 14:11:10 localhost cardmgr[51]: executing: './network start eth0'
May 10 14:11:10 localhost kernel: eth0: NE2000 (DL10019 rev 30): io 0x300,
irq 3, hw_addr 00:00:F4:5E:2D:B2

#cardctl config
Socket 0:
  Vcc 5.0V  Vpp1 0.0V  Vpp2 0.0V
  interface type is "memory and I/O"
  irq 3 [exclusive] [level]
  function 0:
    config base 0x0400
      option 0x60 status 0x00 copy 0x00
    io 0x0300-0x031f [auto]
Socket 1:
  not configured

#cardctl ident
Socket 0:
  product info: "corega K.K.", "corega FastEther PCC-TX"
  manfid: 0xc00f, 0x0000
  function: 6 (network)
Socket 1:
  no product info available

#less /var/lib/pcmcia/stab
Socket 0: Corega PCC-TX Fast Ethernet
0 network pcnet_cs 0 eth0
Socket 1: empty