[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[plamo:00341] Re: サウンド
-
From:Yusuke Iwata
-
Date:Thu, 10 Dec 1998 07:25:04 +0900
- Subject: [plamo:00341] Re: サウンド
- From: Yusuke Iwata <y-iwata@xxxxxxxxxxxxxxx>
- Date: Thu, 10 Dec 1998 07:25:04 +0900
- Posted: Thu, 10 Dec 1998 07:25:01 +0900 (JST)
いわたです。
On Thu, 10 Dec 1998 04:26:43 +0900
Hiroshi Hashibata <hashibata@pop07.odn.ne.jp> wrote:
-> sb_common.c:21: #error You will need to configure the sound driver with
-> CONFIG_AUDIO option.
->
-> make[2]: *** [sb_common.o] Error 1
-> make[2]: Leaving directory `/usr/src/linux-2.0.35/drivers/sound'
-> make[1]: *** [sub_dirs] Error 2
-> make[1]: Leaving directory `/usr/src/linux-2.0.35/drivers'
-> make: *** [linuxsubdirs] Error 2
-> darkstar:/usr/src/linux#
->
-> です。
では、/usr/src/linux/.configの中身のsoundの項を見せてください。
-> > /usr/doc/JF/Soundblaster-16.euc.gz は読みましたか??
-> 読みました。
-> ただ書いてあることがちんぷんかんぷんです。
-> 解説してくれるとありがたいのですが。
えと、まずは、「それもLinuxの現状だ」と理解してください。
サウンドが「ちゃんと」なるようにするのには、結構、手間が
かかります。
あせらず、じっくりと調べてやってください。
だって、設定できるのはあくまでご自身なのですから。
なお、SoundBlaster用の一般的な設定は、
<*> Sound card support
[*]Sound Blaster (SB, SBPro, SB16, clones) support
[*]Generic OPL2/OPL3 FM synthesizer support
[*]/dev/dsp and /dev/audio support
[*]FM synthesizer (YM3812/OPL-3) support
(220)I/O base for SB check from manual of the card
(7)Sound Blaster IRQ Check from manual of the card
(1)Sound Blaster DMA 0, 1 or 3
(5)Sound Blaster 16 bit DMA(_RECUIRED_ for SB16, Jazz16, SMW 5,
6 or
(0)MPU401 I/O base of SB16, Jazz16 and ES1688 Check from manual
of the card
(-1)SB MPU401 IRQ (Jazz16, SM Wave and ES1688) Use -1 with SB16
それから、WEBを調べるテクニックを磨いてください。
どこかに、同じハードウェア構成での設定例があるかもしれません。
あと、うまくいったら、それをどこかで公開しましょう。
# もちろん、このMLでもよいと思いますが。
---
Yusuke Iwata (22y, Male)
Mailto: y-iwata@pop06.odn.ne.jp
PostPet: sario2@geocities.co.jp
- References
-
- [plamo:00337] Re: サウンド, *^^*
- [plamo:00340] Re: サウンド, Hiroshi Hashibata
[検索ページ]
[メール一覧]
Plamo ML 公開システム