[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[plamo:29957] Re: linux-2.6.30.x



  名倉@うちのほうでは雲が厚くて太陽の輪郭も見えなかった です。
 
> こじま@天気が一日ずれてれば日蝕も見えたのになぁ,,です.
> 
> # まぁ,人生,そんなものだけど(苦笑
> 
> From: 名倉昭一 <nagura-s@*********>
> Subject: [plamo:29955] linux-2.6.30.x
> Date: Thu, 23 Jul 2009 11:03:06 +0900
> 
> >     Full SCSIマシンでlibataベース起動不可あらっ でした。
> 
> こういう報告こそ,ハードウェアの構成情報が必要なのでは?
> 
> >   最もlibataベース得意なはずのFull SCSIなマシンlibataベースでは起動してくれない。
> >   まあintel 430VXな時代のマザーなので該当マシンは手元のみと思いますが。
  
  430VX なマザー

  root@hot-557:/home/snagura# lspci
  00:00.0 Host bridge: Intel Corporation 430VX - 82437VX TVX [Triton VX] (rev 02)
  00:07.0 ISA bridge: Intel Corporation 82371SB PIIX3 ISA [Natoma/Triton II] (rev 01)
  00:07.1 IDE interface: Intel Corporation 82371SB PIIX3 IDE [Natoma/Triton II]
  00:11.0 Ethernet controller: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 (rev 02)
  00:12.0 VGA compatible controller: S3 Inc. 86c325 [ViRGE] (rev 06)
  00:13.0 Network controller: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller (rev 02)
  00:14.0 SCSI storage controller: Adaptec AIC-7880U
  root@hot-557:/home/snagura# cat /proc/interrupts
           CPU0
    0:      24588    XT-PIC-XT        timer
    1:          8    XT-PIC-XT        i8042
    2:          0    XT-PIC-XT        cascade
    3:          1    XT-PIC-XT
    4:        110    XT-PIC-XT        serial
    9:       1551    XT-PIC-XT        aic7xxx
   11:        498    XT-PIC-XT        eth2
   12:         61    XT-PIC-XT        b43
   14:          0    XT-PIC-XT        ide0
   15:          0    XT-PIC-XT        ide1
  NMI:          0   Non-maskable interrupts
  ERR:          0

  [    2.976421] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
  [    3.008236] 00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
  [    3.031544] 00:0c: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
  [    3.053567] Uniform Multi-Platform E-IDE driver
  [    3.068917] piix 0000:00:07.1: IDE controller (0x8086:0x7010 rev 0x00)
  [    3.088889] piix 0000:00:07.1: not 100% native mode: will probe irqs later
  [    3.109809]     ide0: BM-DMA at 0xf000-0xf007
  [    3.123136]     ide1: BM-DMA at 0xf008-0xf00f
  [    3.136442] Probing IDE interface ide0...
  [    3.737207] Probing IDE interface ide1...
  [    4.337237] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
  [    4.351234] ide1 at 0x170-0x177,0x376 on irq 15
  [    4.368773] ide-gd driver 1.18
  [    4.384399] PCI: setting IRQ 9 as level-triggered
  [    4.384444] aic7xxx 0000:00:14.0: found PCI INT A -> IRQ 9
  [   19.426065] scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
  [   19.426089]         <Adaptec aic7880 Ultra SCSI adapter>
  [   19.426107]         aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
  [   19.426127]
  [   19.498457] scsi 2:0:0:0: Direct-Access     COMPAQ   ST32550W         6415 PQ: 0 ANSI: 2
  [   19.523033] scsi2:A:0:0: Tagged Queuing enabled.  Depth 32
  [   19.539986]  target2:0:0: Beginning Domain Validation
  [   19.565295]  target2:0:0: wide asynchronous
  [   19.585389]  target2:0:0: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
  [   19.612471]  target2:0:0: Domain Validation skipping write tests
  [   19.630670]  target2:0:0: Ending Domain Validation
  [   20.970851] scsi 2:0:6:0: CD-ROM            MATSHITA CD-ROM CR-506    8S03 PQ: 0 ANSI: 2
  [   20.995597]  target2:0:6: Beginning Domain Validation
  [   21.019031]  target2:0:6: FAST-5 SCSI 5.0 MB/s ST (200 ns, offset 15)
  [   21.043588]  target2:0:6: Domain Validation skipping write tests
  [   21.061761]  target2:0:6: Ending Domain Validation
  [   23.189688] Driver 'sd' needs updating - please use bus_type methods
  [   23.215049]  target2:0:0: FAST-10 WIDE SCSI 20.0 MB/s ST (100 ns, offset 8)
  [   23.240758] sd 2:0:0:0: [sda] 4110000 512-byte hardware sectors: (2.10 GB/1.95 GiB)
  [   23.267429] sd 2:0:0:0: [sda] Write Protect is off
  [   23.282186] sd 2:0:0:0: [sda] Mode Sense: af 00 10 08
  [   23.286944] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
  [   23.315590] PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
  [   23.333112] PNP: PS/2 appears to have AUX port disabled, if this is incorrect

> 
> >   同じくFull SCSIのSocket3なマザーも同様でした。
> >   いずれもlinux-2.6.30.2ではATAドライバー組み込むことにより起動しています。

 Socket3 なマザー 

  root@hot-557:/home/snagura# lspci
  00:05.0 Host bridge: Silicon Integrated Systems [SiS] 85C496 (rev 31)
  00:0a.0 Ethernet controller: Accton Technology Corporation SMC2-1211TX (rev 10)
  00:0b.0 SCSI storage controller: Adaptec AHA-2940/2940W / AIC-7871
  00:0c.0 VGA compatible controller: S3 Inc. 86c764/765 [Trio32/64/64V+] (rev 54)
  root@hot-557:/home/snagura# cat /proc/interrupts
             CPU0
    0:     481562    XT-PIC-XT        timer
    1:          8    XT-PIC-XT        i8042
    2:          0    XT-PIC-XT        cascade
    3:          1    XT-PIC-XT
    4:          2    XT-PIC-XT
    5:       4697    XT-PIC-XT        eth1
    9:       8089    XT-PIC-XT        eth0
   12:       3966    XT-PIC-XT        aic7xxx
   14:          0    XT-PIC-XT        pata_isapnp
   15:          0    XT-PIC-XT        pata_isapnp
  NMI:          0   Non-maskable interrupts
  ERR:          0
  [    4.039856] 00:02: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
  [    4.049879] Uniform Multi-Platform E-IDE driver
  [    4.069892] ide-gd driver 1.18
  [   19.180066] scsi2 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
  [   19.180066]         <Adaptec 2940 SCSI adapter>
  [   19.180066]         aic7870: Single Channel A, SCSI Id=7, 16/253 SCBs
  [   19.180066]
  [   19.197160] scsi 2:0:0:0: Direct-Access     COMPAQ   ST32550W         6416 PQ: 0 ANSI: 2
  [   19.197160] scsi2:A:0:0: Tagged Queuing enabled.  Depth 32
  [   19.197160]  target2:0:0: Beginning Domain Validation
  [   19.211774]  target2:0:0: FAST-10 SCSI 10.0 MB/s ST (100 ns, offset 15)
  [   19.219190]  target2:0:0: Domain Validation skipping write tests
  [   19.219190]  target2:0:0: Ending Domain Validation
  [   20.511136] scsi 2:0:6:0: CD-ROM            YAMAHA   CDR400t          1.0q PQ: 0 ANSI: 2
  [   20.511136]  target2:0:6: Beginning Domain Validation
  [   20.527302]  target2:0:6: Ending Domain Validation
  [   20.550131] Driver 'sd' needs updating - please use bus_type methods
  [   20.560124] sd 2:0:0:0: [sda] 4110000 512-byte hardware sectors: (2.10 GB/1.95 GiB)
  [   20.570460] sd 2:0:0:0: [sda] Write Protect is off
  [   20.570460] sd 2:0:0:0: [sda] Mode Sense: af 00 10 08
  [   20.580126] sd 2:0:0:0: [sda] Write cache: disabled, read cache: enabled, supports DPO and FUA
  [   20.590144] scsi3 : pata_isapnp
  [   20.590144] ata1: PATA max PIO0 cmd 0x1f0 ctl 0x3f6 irq 14
  [   20.600133]  sda:<6>scsi4 : pata_isapnp
  [   20.600133] ata2: PATA max PIO0 cmd 0x170 ctl 0x376 irq 15
  [   20.610140]  sda1 sda2
  [   20.640111] sd 2:0:0:0: [sda] Attached SCSI disk
  [   20.650141] PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
  [   20.650141] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
  [   20.660158] serio: i8042 KBD port at 0x60,0x64 irq 1
  [   20.670136] mice: PS/2 mouse device common for all mice
  [   20.670136] cpuidle: using governor ladder
  [   20.670136] cpuidle: using governor menu
  [   20.690110] TCP cubic registered
  [   20.690110] NET: Registered protocol family 17
  [   20.720100] input: AT Translated Set 2 keyboard as /class/input/input0
  [   20.790091] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x3)
  [   20.870091] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x3)
  [   20.910092] ata2.01: failed to IDENTIFY (I/O error, err_mask=0x3)
  [   20.950092] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x3)
  [   20.990093] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x3)
  [   21.070094] ata2.00: failed to IDENTIFY (I/O error, err_mask=0x3)
  [   25.610163] ata1.01: qc timeout (cmd 0xec)
  [   25.610163] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x5)
  [   35.610314] ata1.01: qc timeout (cmd 0xec)
  [   35.610314] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x5)
  [   65.610766] ata1.01: qc timeout (cmd 0xec)
  [   65.610766] ata1.01: failed to IDENTIFY (I/O error, err_mask=0x5)
  [   70.610842] ata1.00: qc timeout (cmd 0xec)
  [   70.610842] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x5)
  [   80.610992] ata1.00: qc timeout (cmd 0xec)
  [   80.610992] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x5)
  [  110.611445] ata1.00: qc timeout (cmd 0xec)
  [  110.611445] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x5)
  [  110.821497] kjournald starting.  Commit interval 5 seconds
  [  110.821497] EXT3-fs: mounted filesystem with writeback data mode.
  [  110.821497] VFS: Mounted root (ext3 filesystem) readonly on device 8:2.
  [  110.821497] Freeing unused kernel memory: 268k freed
  [  130.901806] 8139too Fast Ethernet driver 0.9.28
  [  130.971785] eth0: RealTek RTL8139 at 0xe800, 00:10:b5:56:91:af, IRQ 9
  [  130.971785] eth0:  Identified 8139 chip type 'RTL-8139B'
  [  138.201896] Console: switching to colour frame buffer device 80x30
  [  138.441892] fb0: S3 Trio64V+ on 0000:00:0c.0, 2 MB RAM, 60 MHz MCLK
  [  139.361928] input: PC Speaker as /class/input/input1
  [  141.781970] sd 2:0:0:0: Attached scsi generic sg0 type 0
  [  141.781970] scsi 2:0:6:0: Attached scsi generic sg1 type 5
  [  142.101968] Driver 'sr' needs updating - please use bus_type methods
  [  142.181976] sr0: scsi3-mmc drive: 6x/6x writer xa/form2 cdda tray
  [  142.197776] Uniform CD-ROM driver Revision: 3.20
  [  142.261989] sr 2:0:6:0: Attached scsi CD-ROM sr0
  [  147.782038] Adding 200772k swap on /dev/sda1.  Priority:-1 extents:1 across:2

> 
> 使っている人には 430VX とか Socket3 だけでどういう SCSI チップを使って
> いるのかが分かるのかも知れないけど,私には分からないので,ドライバオプ
> ションとかも調べようが無いです.

 SiS730S な ECS K7SEM + adaptec AHA2940UW では異常ありませんでした。

> 
> --------
> こじま
> 




Follow-Ups
[plamo:29958] Re: linux-2.6.30.x, KOJIMA Mitsuhiro
References
[plamo:29955] linux-2.6.30.x, 名倉昭一
[plamo:29956] Re: linux-2.6.30.x, KOJIMA Mitsuhiro

[検索ページ] [メール一覧]
Plamo ML 公開システム