[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[plamo:07461] 2.1のsetup中にLILOのインストールに失敗します
-
From:SHIBATA Kazumichi
-
Date:Fri, 27 Oct 2000 18:28:00 +0900
- Subject: [plamo:07461] 2.1のsetup中にLILOのインストールに失敗します
- From: SHIBATA Kazumichi <kibi2@xxxxxxxxxxxxx>
- Date: Fri, 27 Oct 2000 18:28:00 +0900
- Posted: Fri, 27 Oct 2000 18:27:45 +0900
こんにちは、柴田和道です。
SD11月号付録CD-ROMでPlamo2.1をインストールしましたが、
表題のような問題が起きたので報告します。
3台のSCSIディスクに以下のようなパーティションを取り、
ブートセレクタにはPartitionMagic5.01付属のBootMagicを使っています。
*印を付けたパーティションが今回新たに作成したものです。
/dev/sda1 FAT16 PC DOS
/dev/sda2 FAT16 Win98
/dev/sda5 HPFS OS/2 Warp3
/dev/sdb5 HPFS OS/2 Warp4
/dev/sdb6* Linux swap
/dev/sdb7* ext2fs Plamo /
/dev/sdc5 HPFS Warp4 データ用
/dev/sdc6 HPFS Warp4 データ用
/dev/sdc7 HPFS Warp4 データ用
/dev/sdc8* ext2fs Plamo /home
LILOの設定はsimpleを選択して、
/dev/sdb7へインストールしようとしましたが
「LILOのインストールに失敗しました」となって出来ませんでした。
#上記メッセージはうろ覚えです、すいません。
LILO入りの起動FDを作ってあったので、
セットアップ後の再起動はそちらで出来ました。
/etc/lilo.confを見ると、以下のようになっていました。
# LILO configuration file
# generated by 'liloconfig'
#
# Start LILO global section
boot = /dev/sdb7
message = /boot/boot_message.txt
prompt
timeout = 1200
vga = normal
# End LILO global section
# DOS bootable partition config begins
other = /dev/sda4
label = DOS
table = /dev/sda
# DOS bootable partition config ends
# Linux bootable partition config begins
image = /vmlinuz
root = /dev/sdb7
label = Linux
read-only
# Linux bootable partition config ends
# OS/2 bootable partition config begins
other = /dev/sda5
label = OS2
table = /dev/sda
loader = /boot/os2_d.b
map-drive = 0x80
to = 0x81
map-drive = 0x81
to = 0x80
# OS/2 bootable partition config ends
そこで、rootになって直接liloconfigを起動し、
expertでplamoの起動の設定のみ行うと、今度はインストール出来ました。
BootMagicで/dev/sdb7を指定して起動できています。
lilo.confは以下のようになりました。
# LILO configuration file
# generated by 'liloconfig'
#
# Start LILO global section
boot = /dev/sdb7
#compact # faster, but won't work on all systems.
prompt
vga = normal # force sane state
# ramdisk = 0 # paranoia setting
# End LILO global section
# Linux bootable partition config begins
image = /vmlinuz
root = /dev/sdb7
label = plamo
read-only # Non-UMSDOS filesystems should be mounted read-only for checking
# Linux bootable partition config ends
以上です。
足りない情報があれば、ご指摘ください。
--------
柴田 和道 (SHIBATA Kazumichi) kibi2@attglobal.net
[検索ページ]
[メール一覧]
Plamo ML 公開システム