[plamo:17409] サウンド設定について

[Iqbal Abdullah]

いつもお世話になっております。イクバルです。

Plamo 3.0を導入して、サウンドの設定をしようと思っていますが、うまくいっ
ていません。ご存じの方、同じマシン上で設定した方、ご教示をよろしくお願い
します。ちょっと長いですが、以下は各出力のログです。

機種 IBM 300PL 6562-50J Onboard SoundBlaster Pro (互換)

$ dmesg (サウンドサポートをモジュールしたときに)
...
...
Activating ISA DMA hang workarounds.
isapnp: Scanning for PnP cards...
isapnp: Card 'CS4236  Audio'
isapnp: 1 Plug & Play card detected total
...
...

$ dmesg (OSS CONFIG_SOUND_CS4236かな。。セットしたときの出力)
....
Jan 12 19:22:50 lab kernel: ad1848/cs4248 codec driver Copyright (C) by
Hannu Savolainen 1
993-1996
Jan 12 19:22:50 lab kernel: ad1848: WSS/SB detected
Jan 12 19:22:50 lab kernel: ad1848: ISAPnP reports 'WSS/SB' at i/o
0x534, irq 5, dma 1, 3
....

$cat /proc/isapnp
Card 1 'CSCe836:CS4236  Audio' PnP version 1.0 Product version 0.1
  Logical device 0 'CSC0000:WSS/SB'
    Device is not active
    Resources 0
      Priority preferred
      Port 0x534-0x534, align 0x3, size 0x4, 16-bit address decoding
      Port 0x388-0x388, align 0x7, size 0x4, 16-bit address decoding
      Port 0x220-0x220, align 0x1f, size 0x10, 16-bit address decoding
      IRQ 5 High-Edge
      DMA 1 8-bit byte-count compatible
      DMA 0,3 8-bit byte-count compatible
      Alternate resources 0:1
        Priority acceptable
        Port 0x534-0xffc, align 0x3, size 0x4, 16-bit address decoding
        Port 0x388-0x388, align 0x7, size 0x4, 16-bit address decoding
        Port 0x220-0x260, align 0x1f, size 0x10, 16-bit address decoding
        IRQ 5,7,2/9,11,12,15 High-Edge
        DMA 1,3 8-bit byte-count compatible
        DMA 0,1,3 8-bit byte-count compatible
      Alternate resources 0:2
        Priority functional
        Port 0x534-0xffc, align 0x3, size 0x4, 16-bit address decoding
        Port 0x388-0x3f8, align 0x7, size 0x4, 16-bit address decoding
        Port 0x220-0x300, align 0x1f, size 0x10, 16-bit address decoding
        IRQ 5,7,2/9,11,12,15 High-Edge
        DMA 0,1,3 8-bit byte-count compatible
  Logical device 1 'CSC000f:Disabled'
    Device is not active
  Logical device 2 'CSC0010:CTRL'
    Device is not active
    Resources 0
      Priority preferred
      Port 0x120-0xfe0, align 0x7, size 0x8, 16-bit address decoding

$ grep SOUND settings/linux-2.4.20.conf
CONFIG_SOUND=m
# CONFIG_SOUND_ALI5455 is not set
# CONFIG_SOUND_BT878 is not set
# CONFIG_SOUND_CMPCI is not set
# CONFIG_SOUND_EMU10K1 is not set
# CONFIG_SOUND_FUSION is not set
# CONFIG_SOUND_CS4281 is not set
# CONFIG_SOUND_ES1370 is not set
# CONFIG_SOUND_ES1371 is not set
# CONFIG_SOUND_ESSSOLO1 is not set
# CONFIG_SOUND_MAESTRO is not set
# CONFIG_SOUND_MAESTRO3 is not set
# CONFIG_SOUND_FORTE is not set
# CONFIG_SOUND_ICH is not set
# CONFIG_SOUND_RME96XX is not set
# CONFIG_SOUND_SONICVIBES is not set
# CONFIG_SOUND_TRIDENT is not set
# CONFIG_SOUND_MSNDCLAS is not set
# CONFIG_SOUND_MSNDPIN is not set
# CONFIG_SOUND_VIA82CXXX is not set
# CONFIG_SOUND_OSS is not set

/etc/modules.conf
## ALSA?
alias char-major-14      soundcore
alias char-major-116     snd
alias sound-slot-0       snd-card-0
alias sound-service-0-0  snd-mixer-oss
alias sound-service-0-1  snd-seq-oss
alias sound-service-0-3  snd-pcm-oss
alias sound-service-0-8  snd-seq-oss
alias sound-service-0-12 snd-pcm-oss
alias snd-card-0         snd-card-cs4236
options snd-card-cs4236 snd_index=0 snd_port=0x534 snd_cport=0x538
snd_irq=5 snd_dma1=1 s
nd_dma2=0 snd_isapnp=0

最初カーネルをコンパイルしたときにCS_4236を組み込んだですが、ALSAドライ
バを使おと思って上のカーネル設定にしました。modules.confを上のように設定
して、snd-pcm-ossをmodprobeをすると、snd-card-cs4236をunusedのままでした
。cat /proc/asound/cardsでは、no soundcardでした。

もし他の情報が必要になったら、教えてください。

よろしくお願いします。