[plamo:26257] Re: DHCPでのIPの取得(6)

[kohix]

小東 です。

>動いていた時の dmesg と比較してみるのも良いかもしれません。
正常動作してたPlamo Linux 3.3を入れました。
環境はBIOSでモデムをOFFにして、
カーネル2.4.22をフルインストール
/etc/rc.d/rc.modulesにmodprobe sis900の行を追加
3.3ではIPを取得してきます。
でもやりたいのは、Plamo Linux 4.03でのIP取得なんです・・・。

localhost:~# ifconfig -a
eth0      Link encap:Ethernet  HWaddr 00:40:D0:17:0B:C1
          inet addr:192.168.1.15  Bcast:192.168.1.255  Mask:255.255.255.0
          UP BROADCAST NOTRAILERS RUNNING  MTU:1500  Metric:1
          RX packets:997 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1073 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:741972 (724.5 Kb)  TX bytes:138862 (135.6 Kb)
          Interrupt:11 Base address:0x1000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:65 errors:0 dropped:0 overruns:0 frame:0
          TX packets:65 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:4398 (4.2 Kb)  TX bytes:4398 (4.2 Kb)

localhost:~# dmesg
Linux version 2.4.22 (root@test) (gcc version 2.95.3 20010315 (release)) #1 Wed Sep 3 18:51:00 JST 2003
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
 BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000eac00 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000000b7f0000 (usable)
 BIOS-e820: 000000000b7f0000 - 000000000b7ffc00 (ACPI data)
 BIOS-e820: 000000000b7ffc00 - 000000000b800000 (ACPI NVS)
 BIOS-e820: 00000000fff80000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
183MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 47088
zone(0): 4096 pages.
zone(1): 42992 pages.
zone(2): 0 pages.
ACPI disabled because your bios is from 2000 and too old
You can enable it with acpi=force
ACPI: RSDP (v000 PTLTD                                     ) @ 0x000f6fb0
ACPI: RSDT (v001 PTLTD    RSDT   0x06040000  LTP 0x00000000) @ 0x0b7fc9ae
ACPI: FADT (v001 SHARP  Race     0x06040000 PTL  0x000f4240) @ 0x0b7ffb64
ACPI: BOOT (v001 PTLTD  $SBFTBL$ 0x06040000  LTP 0x00000001) @ 0x0b7ffbd8
ACPI: DSDT (v001  MITAC     7120 0x06040000 MSFT 0x0100000b) @ 0x00000000
Kernel command line: BOOT_IMAGE=Linux ro root=302
Initializing CPU#0
Detected 701.606 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 1399.19 BogoMIPS
Memory: 182912k/188352k available (1752k kernel code, 5052k reserved, 712k data, 112k init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 8192 (order: 3, 32768 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 128K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0383f9ff 00000000 00000000 00000000
CPU:             Common caps: 0383f9ff 00000000 00000000 00000000
CPU: Intel Celeron (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
Checking for popad bug... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20030813
ACPI: Interpreter disabled.
PCI: PCI BIOS revision 2.10 entry at 0xfd9de, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: ACPI tables contain no PCI IRQ routing entries
PCI: Probing PCI hardware (bus 00)
PCI: Using IRQ router SIS [1039/0008] at 00:01.0
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
Real Time Clock Driver v1.10e
pcnet32.c:v1.27a 10.02.2002 tsbogend@alpha.franken.de
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
hda: HITACHI_DK23BA-20, ATA DISK drive
hdc: UJDA330, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 39070080 sectors (20004 MB) w/2048KiB Cache, CHS=2432/255/63
Partition check:
 hda: hda1 hda2
Promise Fasttrak(tm) Softwareraid driver 0.03beta: No raid array found
Highpoint HPT370 Softwareraid driver for linux version 0.02
Guestimating sector 39069119 for superblock
driver for Silicon Image(tm) Medley(tm) hardware version 0.0.1: No raid array found
SCSI subsystem driver Revision: 1.00
kmod: failed to exec /sbin/modprobe -s -k scsi_hostadapter, errno = 2
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 1024 buckets, 8Kbytes
TCP: Hash tables configured (established 16384 bind 16384)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 112k freed
Adding Swap: 248968k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
Trident 4DWave/SiS 7018/ALi 5451,Tvia CyberPro 5050 PCI Audio, version 0.14.10h, 19:03:41 Sep  3 2003
PCI: Found IRQ 5 for device 00:01.4
trident: SiS 7018 PCI Audio found at IO 0x1400, IRQ 5
ac97_codec: AC97 Audio codec, id: CRY52 (Cirrus Logic CS4299 rev D)
ac97_codec: AC97 Modem codec, id: SIL33 (Unknown)
sis900.c: v1.08.06 9/24/2002
PCI: Found IRQ 11 for device 00:01.1
eth0: SiS 900 Internal MII PHY transceiver found at address 1.
eth0: Using transceiver found at address 1 as default
eth0: SiS 900 PCI Fast Ethernet at 0x1000, IRQ 11, 00:40:d0:17:0b:c1.
eth0: Media Link On 100mbps full-duplex
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
localhost:~#

---
小東 哲也